Polyaniline encapsulated Ti-MOF/CoS for efficient photocatalytic hydrogen evolution

We report the study of conductive polyaniline (PANI) chain embedded Ti-MOF functionalized with CoS as a cocatalyst for hydrogen evolution reaction (HER) application. The post synthetically modified hybrid photocatalyst PANI/Ti-MOF/CoS greatly influences the redox and e^? ? h⁺ separation process and exhibits an impressive rate of HER (～1322 μmol h^?1g^?1), suppressing the pristine Ti-MOF (～62 μmol h^?1g^?1) with apparent quantum yield (AQY) of ～3.2 and transient current response of ～46.4 μA cm^?2. In this system, Ti-MOF provides the circulation of Ti³⁺ and Ti⁴⁺ to the reaction of photocatalytic H₂ generation, where the additional PANI and CoS amended the performance of H₂ production through electron enrichment and thereby improving the stability and integrity of Ti-MOF. The Electrochemical studies demonstrated increased photocurrent by interweaving Ti-MOF crystal with PANI through cation-π interaction thereby enhancing interface connection and then promoting electron transfers. The charge dynamics revealed the initial charge transfer from photoexcited PANI to encapsulated MOF framework to boost the photocatalytic performance of the system. Further, the electron movement at the Ti-MOF/CoS interface is investigated through work function and electrochemical potential of electrons (Fermi level). DFT results demonstrate the importance of CoS in improving the photocatalytic performance of hybrid Ti-MOF catalyst, which leads to superior catalytic behaviour. These results establish that the encapsulation of catalytic active sites inside MOFs with desirable energy band gaps would be an ideal choice for the production of solar fuels.     

基于拼接缝自适应消除和全景图矫直的快速图像拼接算法

针对图像拼接存在色差过渡不均匀、图像倾斜扭曲及拼接效率低的现象，提出一种基于拼接缝自适应消除和全景图矫直的快速图像拼接算法。首先，用尺度不变特征变换（SIFT）提取图像指定区域特征点并用双向K近邻（KNN）算法进行图像配准，有效提高算法效率；其次，利用动态规划思想提出自适应公式找到最优拼接缝并用图像融合算法对其自适应消除，解决拼接缝色差过渡不均匀问题；最后，针对累积拼接误差形成全景图倾斜的现象，利用边缘检测算法提出自适应拟合四边形矫直模型，把原始全景图矫直为一个全新的全景图。所提算法与分块图像拼接和二叉树图像拼接算法相比，图像质量提升了5.84%~7.83%，拼接时间仅为原来的50%~70%。实验结果表明，该算法不仅通过自适应更新机制减少不同图像背景下拼接缝色差过渡不均匀的现象，从而提高了图像质量；而且提高了拼接效率，降低了全景图倾斜扭曲程度。     

高速旋转机械用消除频率混叠现象的小波变换算法研究

高速旋转机械由于其工作转速高、控制精度高，其故障信号又属于微弱突变信号，造成常规监测方法准确率偏低，成为制约高速旋转机械故障监测进一步发展的最大障碍。本文设计了一种消除小波分解和重构过程中产生的频率混叠的算法。该算法利用傅里叶变换和傅里叶逆变换构成Mallat小波变换在分解和重构过程中所需的严格正交镜像滤波器，从而达到Mallat小波变换过程中必须具有的理想截止特性，最终去除掉多余的频率成分。利用改进前后的小波算法对实际信号进行分析，结果表明，本文设计的Mallat小波变换改进算法可消除信号分析中出现的频率混叠现象。     

某矿快速掘进最优炮孔间距的选择

山西某矿5308底抽巷在掘进过程中速度慢、效率低，直接影响工作面的瓦斯抽采，为了改善上述情形，对炮孔间距进行研究。通过使用ANSYS软件对不同炮孔间距下快速掘进效果的模拟分析，并经现场验证，得出了适应该矿的最佳炮孔间距。结果表明：炮孔间距为500 mm时，爆破产生裂隙发育范围和岩石损伤区域都最大，快速掘进的效果最好。     

飞秒激光光斑轮廓的傅里叶描述子重建及特征提取

在利用飞秒激光对单晶硅材料进行微尺度烧蚀时,衍生的等离子体发光光斑中蕴含着大量的加工信息。如何有效提取光斑图像的几何特征信息,对研究飞秒激光烧蚀加工工艺过程具有重要意义。轮廓特征是描述激光光斑最重要的特征之一,本文着重分析了等离子体光斑轮廓特征与光斑运动规律间的关系及光斑运动情况分类方法。首先,考虑到光斑微弱的特性,对光斑图像进行增强处理。其次,采用链码方法提取光斑轮廓特征,并利用傅里叶描述子低频特性,选取少量的描述子重建光斑图像轮廓特征,减少了复杂的计算量,有效提高了光斑图像分类的速度与质量。最后,运用Hu不变矩特征证明傅里叶描述子用于提取激光光斑对轮廓特征的有效性。     

Eliciting and measuring hesitance in decision-making

Hesitance is an innate human psychological phenomenon pervasive in our daily life. Although it is very complex and still not fully understood, there have been many studies related to this interesting topic. In this study, we proposed two fundamental problems about hesitance: the first is the generating problem, which is related to how to elicit hesitance information from human thinking; the second is the measuring problem, which is related to how to devise effective and reasonable methods to measure hesitance degrees from given hesitance information. With these two fundamental questions, we first discussed and analyzed several examples in real life involving hesitance, showing that it can indeed be recorded and represented. Then we roughly classified the hesitance information into two major classes: static hesitance and dynamic hesitance. Some simple and interesting methods were proposed to elicit hesitance, and more reasonable methods were proposed to measure the hesitance degree from the two classes of hesitance information. All methods that have been discussed in this study try to avoid complexity in every aspect while reserving strictness and reasonability; therefore, the present study provides suitable information for practitioners with different backgrounds.     

Effect of temperature on fast forging process of Mg-Ni samples for fast formation of Mg2Ni for hydrogen storage

Fast-Forging was used as a Severe Plastic Deformation technique to process Mg/Ni fine powder mixtures at a ratio corresponding to the eutectic composition. The samples were processed at different temperature, increased successively from room temperature up to above 500 °C. The one shock forging operation led to a reduction rate comprised between 80 to more than 90% depending of the applied temperature. Interestingly, a threshold temperature was pointed out for which amounts of the binary Mg₂Ni alloy were directly synthesized in increasing proportions when increasing temperature. A maximum amount of Mg₂Ni was synthesized according the nominal proportions at the highest applied temperature. Besides, numerical simulations were developed to consider and integrate to the forging process, the heat arising from the mechanical energy at deformation. Interestingly the total temperature at shock – heat applied to and heat developed in – indicates that the threshold temperature correspond well with the eutectic temperature as reported in the phase diagram. Early hydrogenation cycles suggest that both mechanical defects in brittle Mg and presence of amounts of Mg₂Ni as catalyst should be combined to optimize the hydrogenation characteristics.     

Development of a fast atom beam gun for surface-activated bonding

Surface-activated bonding (SAB), also called room-temperature bonding, is used in three-dimensional integration technology for semiconductor devices. An Ar fast atom beam (FAB) is used for SAB. However, conventional FAB guns must be replaced after hundreds of minutes of irradiation because carbon abrasion powders are generated by Ar ions sputtering in the gun. Therefore, this study develops a novel FAB gun with improved lifetime. The proposed FAB gun applies magnetic fields to guide Ar ions to reduce sputtering in the gun and improve irradiation efficiency. The proposed FAB gun indicates the possibility of improving gun lifetime.     

基于高光谱图像的改进SIFT特征提取与匹配

针对尺度不变特征变换(SIFT)算法所提取图像特征点数量少、误匹率高的问题,提出了一种基于高光谱图像的改进SIFT算法。首先,依据传统SIFT算法中高斯金字塔的构造思想,结合在不同波段下的高光谱图像具有相同宏观特征的特点,首次用高光谱图像作为原始算法中经高斯变换产生的图像,使得检测到的具有实际意义的特征点数量大幅增加;其次,传统SIFT算法以及大量的改进方法都只通过目标象元邻域范围内的像素信息来构造特征描述符,而忽略了像素点的位置信息,文中将目标象元的位置信息纳入了特征描述符,在特征描述符的匹配阶段,在利用邻域范围内的像素信息进行粗匹配之后,利用特征描述符中的位置信息进行精细匹配。仿真实验结果表明在限定最优值与次优值之比的情况下,采用高光谱图像构造高斯金字塔的方式能显著增加特征点的提取数量,更多地挖掘出图像中的极值点;在特征描述符中加入目标象元的位置信息作为特征点匹配第二阶段的判断依据,正确匹配数量达到原方法的59倍以上,极大提升了算法的匹配性能。